---
Title: Preamplifier, filters, equalizers and cables – AudioLab
---

# Preamplifier, filters, equalizers and cables

![A ten-band graphic equalizer in brushed aluminium, one ±12 dB control per octave from 32 Hz to 16 kHz and a master level](figures/equalizer.jpg)

Line-level devices: the interface output drives them directly and their output goes straight to the inputs. Wiring: *Stereo* for the response, *Stereo, references first* for distortion and noise ([Which wiring](wiring.html#which-wiring)).

## Line preamplifier

**Connect:** *Wiring* **Stereo** (IN 1 reference L, IN 2 output L, IN 3 reference R, IN 4 output R) for the response; **Stereo, references first** (IN 1/2 references, IN 3/4 outputs) for distortion and noise – see [Which wiring](wiring.html#which-wiring).

| What | Task | Set | Good value |
| --- | --- | --- | --- |
| Gain and flatness | Gain & phase | about 0.25 V (−20 dBFS at 2.45 V full scale); volts on for true gain | ±0.2 dB, 20 Hz – 20 kHz |
| Channel balance | Gain & phase, both channels | repeat at 3–4 volume positions, Keep each one | below 0.5 dB (cheap pots 2–3 dB at low volume) |
| THD+N | THD+N meter | level for about 1 V output | 0.001–0.005 % |
| Headroom | THD vs level | 1 kHz up to clipping | clips above 2–3 V |
| Noise | Noise & S/N | volume down and up; Details give the density at 1 kHz in nV/√Hz (calibrated) | above 100 dB; a few tens of nV/√Hz at the output |
| Crosstalk | Crosstalk | stereo wiring | −70 to −90 dB |
| Output impedance | Output Z | Load 600 Ω | below 100–600 Ω |

## Filters and crossovers

| What | Task | Set | Look at |
| --- | --- | --- | --- |
| Response | Gain & phase | about 0.25 V, 24 points / octave | −3 dB points, slope (dB/octave), passband ripple |
| Phase of crossover branches | Gain & phase, or **Stepped sine** with a reference | each branch, Keep | phase difference of the branches at the crossover frequency; Stepped sine keeps the phase far into each branch's stopband |
| Deep stopband | Stepped sine | more averages | attenuation below −60 dB, and its phase |
| Distortion and noise (active) | THD+N meter, Noise & S/N, THD vs level | as a preamplifier | as a preamplifier |

A **passive crossover** depends on its load: measure it with the loudspeaker or a dummy (resistor and coil), not unloaded.

## Equalizers and tone controls

| What | Task | Set |
| --- | --- | --- |
| Flat position (all at 0) | Gain & phase | should be ±0.5 dB |
| Each band | Gain & phase | Keep every setting: centre, width (Q) and boost of each band |
| Overload with boost | THD vs level | with +10 dB boost: where clipping starts |
| Channel match | Gain & phase, both channels | same setting = same curve? |

## Cables

Short interconnects do nothing measurable in the audio band. Measuring makes sense for **faults** and for **long or loudspeaker cables**.

| What | Task | When it makes sense |
| --- | --- | --- |
| Hum, interference | Spectrum | broken shield, ground loop |
| Treble loss | Gain & phase | long cable (10 m and more) after a source with a higher output impedance |
| Crosstalk | Crosstalk | multicore cables, long parallel runs |
| Loudspeaker cable resistance | Output Z at the cable end, Load 8 Ω | how much the cable adds to the amplifier's output impedance |
| Fault (open, short) | Level meter, Spectrum | quick check that the signal passes on both channels |
