---
Title: Tasks – AudioLab
---

# Tasks

Every task of the MEASUREMENT panel in short: what it is for, how to run it and what the bar shows. **Details →** leads to its page. Which tasks to run for a particular device: [What to measure](guide.html).

## Signal and noise

### Level meter

Levels of all four inputs as bars – for calibration, setting levels and spotting overload. RMS in dBFS (volts, dBV, dBu after calibration, watts with a load), the strongest tone (the generator's while it plays) and the peak; *CLIPPING* at 0 dBFS. [**Details →**](spectrum.html#level-meter)

### Spectrum

What is in the signal: hum, interference, harmonics. **RUN**; keys **Log f** (log frequency axis), **Peaks** (the ten strongest lines marked) and **Spectrogram** (the last minute as colour). [**Details →**](spectrum.html)

### Noise & S/N

Signal-to-noise ratio. Device input connected, **SINGLE**: a tone, then the noise with the generator silent. The bar: S/N unweighted, A-weighted and ITU-R 468 – against the tone, 1 V at a calibrated output, or the level at a distortion limit (a tape's full modulation). *interface limit* when the device is as quiet as the interface. [**Details →**](noise.html)

## Distortion

### THD+N meter

Distortion at one frequency. SIGNAL 1 kHz at the device's rated input in volts – a line device about 0.25–1 V – **RUN** while adjusting. The bar: THD+N (or SINAD), THD, the fundamental; Details: harmonics H2…, noise, the largest spur, the reference row (the measurement floor). Key **Scope**: the waveform and its residual. [**Details →**](distortion.html)

### THD vs level, THD vs frequency

Distortion over level (−60 to −6 dBFS, from millivolts to about 1 V) or frequency (20 Hz – 20 kHz), **SINGLE**. The bar: lowest THD+N and the **power (or level) at the distortion limit** – e.g. power at 1 % THD+N with a load. *X* and *Y* redraw the same points over power, output level, % or harmonics. [**Details →**](distortion.html#thd-vs-level-thd-vs-frequency)

### IMD, IMD vs level, Multitone

Two-tone intermodulation (SMPTE, DIN, CCIF), over level too; **Multitone** plays 31 tones at once and shows the distortion and noise between them – the whole band in a second, for adjusting live. [**Details →**](imd.html)

## Frequency response

### Gain & phase

Frequency and phase response with a chirp, **RUN**. The bar: gain at 1 kHz, −3 dB points, the band edges, L−R balance. With reference and output on different kinds of input (M4 front against line), **Save as loop** once and the difference is taken out. [**Details →**](response.html)

### Stepped sine

The response tone by tone: slower, but it measures a DAC on its own clock and keeps the phase deep into a filter's stop band. [**Details →**](response.html#stepped-sine)

### Phono preamplifier (RIAA)

Gain & phase or Stepped sine through a −40/−60 dB attenuator, reference after it, ANALYSIS → *Compare with phono curve*: the chart shows the deviation from RIAA. *Inverse RIAA* plays distortion tests as from a record. [**Details →**](response.html#phono-preamplifier-deviation-from-riaa)

## Output and channels

### Output Z

Output impedance from the level without and with a load: *On the device output* = **Nothing (open)**, **RUN**; connect the resistor and choose it. The bar: Z and the damping factor. No calibration needed. [**Details →**](output-z.html)

### Crosstalk

Channel separation over frequency, stereo wiring, **SINGLE**: each channel driven alone. Filled points are measured crosstalk, open circles only an upper bound where noise or hum hides it. [**Details →**](crosstalk.html)

## Devices with tasks of their own

### Tape recorder

**Speed & flutter** (3150 Hz, weighted and unweighted wow and flutter, azimuth at 10 kHz, the flutter spectrum), **Tape response** (record → playback) and **Test tape** (playback response from a test tape). [**Details →**](tape.html)

### Turntable

**Test record**: speed, crosstalk and azimuth, channel balance, response, tracking ability, anti-skating, the arm resonance, wow & flutter, rumble and IMD from the Ortofon Test Record or the Analogue Productions Ultimate Analogue Test LP; the tracks in any order, each recognised as it plays, or clicked first; its **Setup** view takes the turntable through the alignment step by step. [**Details →**](turntable.html) · [**Setup, step by step →**](turntable-setup.html)

### Player

A CD player, streamer or portable player: **Create test file…**, play it on the player while AudioLab runs. It measures level, THD+N, linearity, dynamic range, noise, crosstalk, response, IMD and jitter (J-test) in 2 min 50 s. [**Details →**](player.html)
