---
Title: Turntable setup, step by step – AudioLab
---

# Turntable setup, step by step

The **Setup** view of the **Test record** task takes a turntable through its alignment one step at a time: it reads the tracks of a test record as they play, says which setting is off and which way to turn it, and which tracks to play again to check it. It measures nothing of its own – it reads the same tracks as the other views ([Turntable and test record](turntable.html)) and turns them into a procedure.

![The Setup view after a whole side of the Ortofon record: "Your turntable is set up well", 6 of 6 OK; Anti-skating good; Azimuth good, channels leak alike, −1.2 dB, the dot in the green band and the figure beside it, −1.2 dB · green: within ±2 dB; every track of the strip green](figures/setup_done.jpg)

## What you need

- A **test record**: the **Ortofon Test Record** or **The Ultimate Analogue Test LP** (Analogue Productions). These two are known by name, track by track.
- A **phono preamplifier**, or an amplifier with a phono input and a line output (often *REC OUT*).
- An **audio interface** with a stereo line input, and two cables from the preamplifier's outputs to it.
- The cartridge maker's **tracking force** (in its leaflet or on its website).

## Before the first play

1. Turntable → phono preamplifier, with the ground wire on its GND terminal; preamplifier output **L** and **R** → the interface's line inputs. Nothing goes to the interface's outputs: the record plays, AudioLab only listens.
2. **CONNECTIONS**: your interface, *Wiring* **Stereo, references first** (the preamplifier's L and R to In 3 and In 4).
3. **MEASUREMENT** → Turntable → **Test record**. The view above the chart opens on **Setup**.
4. **ANALYSIS** → *Test record*: the record on the platter.
5. Set the arm as the turntable's manual says: balance it to zero, set the force the cartridge maker gives and the **anti-skating to the same number**.

The steps read *Not yet* until their tracks have played; Record & input reads *Checking* until a few tones have shown which record plays.

![The Setup view before the first play: "Keep playing the record – 0 of 6 steps measured", play the record from track 1 to the end of the side; Tracking force, Anti-skating and Azimuth not yet, each with the numbers of its tracks; in the strip tracks 1 to 14 orange for the setup, the complete-test track 15 dimmed](figures/setup_first_play.jpg)

## The first play: a whole side

Press **RUN** and play the record **from the first track to the end of the side** – not track by track. Each track is recognised as it plays and fills its steps; the order does not matter, a track played twice counts once (the later play).

The strip under the panel shows what each track is for:

| Colour | Meaning |
| --- | --- |
| orange | for the setup – play it now |
| grey | for the setup – not yet |
| dimmed | only for the complete test (response, distortion, arm resonance, noise) – not needed for the setup |
| green | heard |
| cyan | playing now |

The tracks of the setup:

| | Ortofon Test Record | The Ultimate Analogue Test LP |
| --- | --- | --- |
| Signal (phono correction, overload) | 1–4 (sweeps) | A1, A6, A7 |
| Speed | 5 (1 kHz; 6–8 read it too) | A10 (3150 Hz) |
| Tracking force | 9–14 (315 Hz, 50–100 µm) | – (none on the record: balance the arm and set the maker's force) |
| Anti-skating | 9–14 | B1 (rising ramp) |
| Azimuth | 5–8 (1 kHz, one channel each) | A2, A3 |

Each card also lists the numbers of its own tracks, so you can go straight back to them.

If the tones heard are not on the record chosen, the first card says so, and names the record they fit:

![Record & input to adjust: 3 of the 3 tones and sweeps heard are not on the Analogue Productions record; what to do: the tones heard fit the Ortofon Test Record – choose it under ANALYSIS → Test record, what was heard is judged again at once](figures/setup_wrong_record.jpg)

## Reading the panel

**At the top, the verdict** – one line:

- **✓ Your turntable is set up well** – every step within its limits;
- **! Adjust the …** – the step to adjust now; its card is open below;
- **Keep playing the record – n of 6 steps measured** – and what to play.

Under it, what is playing now (*Now: track …*, *Listening – between tracks*, *Stopped – press RUN to go on*).

**The cards**, in the order of the alignment: Record & input, Signal, Speed, Tracking force, Anti-skating, Azimuth; at the bottom a *Note* on what no adjustment changes. Each card has a label:

| Label | Meaning |
| --- | --- |
| Good | within its limits |
| Adjust | to set – the card is open with what to do |
| Not yet / Next | its tracks have not played yet; *Next* is the one waited for |
| After the force, After the signal | measured, but another step comes first: the force before the anti-skating and the azimuth (a stylus sitting unevenly changes the crosstalk too), the signal before everything it reads |
| Checking, Playing | being read: the first tracks of the record, or a group of tracks played again |
| Note | for information only |

Only one card is open at a time – the step to deal with now. It says what is wrong in one sentence, then **What to do** in two or three short steps, ending with the tracks to play again. A folded part under it gives the longer way (setting the force from zero, where the speed adjustment is, turning the headshell). The card stays open while you adjust it, also once it turns green, until a track of another step plays.

## Adjusting

One thing at a time, from the top:

1. Read the open card and do what it says.
2. Play the tracks named on it – the **whole group**, from its first track: 5 to 8, 9 to 14. A group is judged once its last track has played; until then its cards read *Playing*.
3. The card turns **Good**, or stays **Adjust** with the new figures; then the next step opens.

![Speed to adjust while track 5 plays: −1.59 %, the platter turns too slow; what to do: turn the speed adjustment a little up, play track 5 again; on the scale the dot left of the green ±0.3 % band and a ring inside it for the play before](figures/setup_speed_adjust.jpg)

Keep **RUN** running between plays: there is no need to stop. Only after putting **another record** on the platter press **STOP** and **RUN**: the tones of the record before would otherwise be read as tracks of the new one. The play before stays on the card as a mark – a ring on the speed scale, a thin line on the distortion bars, *before: …* in the text – so you see which way the change went. The marks survive STOP and RUN; another record chosen clears them.

![Anti-skating to adjust: R distorts more on every tracking track, about 1.6 times L – the anti-skating is too low; what to do: turn the dial a little up, half a step at a time, and play tracks 9–14 again](figures/setup_antiskating_adjust.jpg)

![The same card after the dial was turned up and tracks 9–14 played again: "The anti-skating is right", the card kept open with a green frame – leave it where it is](figures/setup_held_good.jpg)

### What each step reads and says

| Step | What it reads | What it may say |
| --- | --- | --- |
| **Record & input** | the tones heard against the record chosen | tones that are not on this record: another record is playing (the one they fit is named) |
| **Signal** | the sweeps against the record's curve, the level | the phono correction missing or applied twice; input overload; a channel bringing no signal, or coming and going (a loose contact) |
| **Speed** | the 1 kHz (or 3150 Hz) tone | too fast or too slow, beyond ±0.3 %: turn the pitch or speed trimmer, play the tone again |
| **Tracking force** | distortion of L and R on the tracking tracks | R distorting far more, or both past 3 %: a little more force, the anti-skating set with it; close to the limit: the upper half of the maker's range gives more margin |
| **Anti-skating** | how L and R distort against each other on the tracking tracks or the ramp | R worse on every track: too low, turn it up; L worse or mistracking: too high, turn it down – it should not read more than the force |
| **Azimuth** | crosstalk L→R against R→L from the one-channel 1 kHz tracks | one channel leaks more: turn the headshell a hair about its long axis |

### The azimuth

The azimuth comes last: the force and the anti-skating move the crosstalk too.

- Play **all four** Ortofon tracks 5–8 every time (on the Analogue Productions record A2 and A3). A single pair may read a little differently, so the azimuth is the **average** of the play. While they play, the figure moves; it counts once track 8 has played.
- The **Azimuth** view shows one point per play of the four tracks and compares it with the play before: *smaller than the play before* (the turn helped), *larger* (turn the other way), *past zero – back a little*.
- Turn by a hair – a fraction of a degree is enough. A headshell that does not turn can be tilted with a thin shim of paper under one side of the cartridge.
- How far off is too far – the difference L→R − R→L once the tracks have played:

  | L→R − R→L | What it means | What to do |
  | --- | --- | --- |
  | up to 2 dB | within the spread of tracks and records | leave it |
  | 2–3 dB | a slight lean of the stylus, or within what tracks and records differ by | turn a hair; if the figure does not move, leave it |
  | 3–5 dB | the stylus leans | adjust it; with a second record, check on it too |
  | over 5 dB | more than the azimuth | first the tracking force and anti-skating, the cartridge seated firmly, the contacts and the cable |

- **Why ±2 dB.** One play repeats within a tenth or two of a decibel, but different pairs of tracks and the two records read a few decibels apart on the same turntable; AudioLab takes ±2 dB as right.
- **A figure that moves by more than about 1 dB from one play to the next with nothing turned is not the azimuth** – plays repeat within a few tenths of a decibel. Look at the contacts at the headshell and the turntable's cable: a failing contact raised one channel's crosstalk by 2–3 dB before the channel began to drop out.

![The Azimuth view after four plays of tracks 5–8 without anything turned: points at −1.3, −1.5, −1.5 and −1.4 dB (L→R about −31.7, R→L −30.3 dB), all inside the green ±2 dB band – the spread between plays a tenth or two of a decibel; the title "Azimuth OK: L→R and R→L within 1.4 dB over tracks 5–8"](figures/setup_azimuth_view.jpg)

## What the setup does not change

The *Note* at the bottom lists what the alignment cannot move: an arm resonance outside 8–12 Hz (only a lighter or heavier headshell or cartridge moves it), treble falling above about 10 kHz (the cartridge with its cable and the preamplifier input), rumble, and a short pulse pointing down in the square wave (a preamplifier that inverts the polarity – harmless).

## When it is done

**✓ Your turntable is set up well.** For the complete test – response, distortion, arm resonance, noise – play also the dimmed tracks; the other views show them. **Report** gives the protocol with the setup, every chart of the record and the details; **Export** in the Setup view saves the panel as a picture or the results as CSV.

## Limits

The advice is written for an ordinary turntable: an arm with a counterweight and a force ring, an anti-skating dial, a headshell held by a screw or a collar, a pitch control or speed trimmer. It does not cover arms with the force set by a spring (dynamic balance), tangential arms, P-mount cartridges, or quartz-locked turntables without a speed adjustment – the readings hold, the advice on where to turn does not.

## Trying it without a turntable

Choose the interface **AudioLab Simulator** and the device **Turntable + phono preamp (test record)**: a turntable out of alignment, so the Setup view has something to say. Then switch to **Turntable + phono preamp, aligned (test record)** and play the tracks again: the steps turn Good and the marks show the play before.

## How the groove works

Why a one-channel track leaks into the other channel, and what a leaning stylus or an unbalanced anti-skating does to it, is drawn step by step in the [Stereo groove simulator](groove-simulator.html) – in the browser, without a turntable.
