---
Title: Wiring and reference – AudioLab
---

# Wiring and reference

![Measurement boxes on a desk, joined by cables: a dummy load with speaker terminals, an attenuator with a selector switch and a box with RCA terminals and a toggle switch](figures/wiring_boxes.jpg)

How to connect a device, what the reference input does in each task and which wiring to choose.

## Wiring presets

**CONNECTIONS → Wiring** sets what each input carries:

| Wiring | IN 1 | IN 2 | IN 3 | IN 4 |
| --- | --- | --- | --- | --- |
| **Stereo** (default) | reference L | output L | reference R | output R |
| **Stereo, references first** | reference L | reference R | output L | output R |
| **Stereo, one reference** | reference (generator L) | – | output L | output R |
| **Mono** | you choose the *Reference* and *Device output* inputs | | | |
| **External DAC (USB), no reference** | – | – | DAC output L | DAC output R |

**Under the Wiring box AudioLab lists every cable** for the current settings, one line per cable, from → to, with the generator output from Settings → Audio → *Generator outputs*, the inputs chosen for Mono and the DAC's name. For example *Stereo, references first* on outputs 3–4:

- OUT 3 → device input L + In 1 (reference L, Y split)
- OUT 4 → device input R + In 2 (reference R, Y split)
- Device output L → In 3
- Device output R → In 4

The dot before each line has the channel's colour (L blue, R orange), the same as the **L / R** keys and the curves. "Y split" means the output feeds the device and the reference input at once through a Y-cable. The same list appears in the **Info** window above the chart, in the export header and in the report.

### Generator outputs and connectors

The interface plays the test signal on both outputs of the pair chosen in Settings → Audio → *Generator outputs*: **Outputs 1–2** (OUT 1 = L, OUT 2 = R) or **Outputs 3–4** (OUT 3 = L, OUT 4 = R). Each pair has its own output calibration.

On a **MOTU M4**:

![MOTU M4 rear panel: power switch, MIDI in and out, USB-C, LINE OUT 3–4 and MONITOR 1–2 as RCA, LINE OUT 3–4 and MONITOR 1–2 as quarter-inch jacks, LINE IN 3–4](wiring/motu_m4_rear.jpg)

![MOTU M4 front panel: combo inputs IN 1 and IN 2 with gain, 48V and MON buttons, the INPUT MONITOR MIX knob (from INPUT to PLAYBACK) with the 3-4 button, the level display, the MONITOR volume knob and the headphone output](wiring/motu_m4_front.jpg)

- Outputs 1–2 are the rear MONITOR outputs behind the volume knob and the direct monitor mix; outputs 3–4 the rear LINE OUT 3–4 at a fixed level – better for measuring, a knob cannot upset the calibration.
- The quarter-inch outputs are balanced and not cross-coupled: **never plug a TS (mono) jack into them**, it shorts the negative leg and distorts (MOTU manual). Use **TRS** cables there, and the unbalanced **RCA outputs** (each RCA pair mirrors its quarter-inch pair, up to +9.5 dBu) for unbalanced gear. Calibrate the outputs from the connector you measure with.
- In 1/2 are the front combo inputs with a preamplifier, In 3/4 the rear line inputs. The front inputs are a little worse (THD+N −100 against −106 dB) and not flat: a high-pass near 16 Hz (−2.15 dB and +40° at 20 Hz) and a low-pass near 75 kHz (−0.3 dB at 20 kHz), measured against the line inputs.
- The direct monitor (MON and 3-4 buttons, INPUT MONITOR MIX knob) acts on MONITOR 1–2 and the headphones – switch it off when measuring from them and turn the knob to PLAYBACK.

## The reference

The **reference** is the signal **right before the device** – exactly what goes into it, recorded at the same moment and on the same clock as the device output. With it AudioLab removes the generator's and converters' own flaws (what is in the reference is not the device's fault: the *measurement floor*), measures gain and phase as the ratio output / reference, and needs no exact generator level (a divider or a loading device does not matter).

| Task | What the reference does | Without a reference |
| --- | --- | --- |
| Spectrum | its own curve beside the output (**REF**): the interface floor | output only |
| Level meter | input label only ("In 1 · L ref") | same |
| THD+N meter | *reference* row: distortion and noise of the measurement path; output close to it = you measure the interface | output only |
| THD vs level / frequency | dashed curve; *Subtract reference THD* estimates the device's own THD | output only |
| IMD, IMD vs level | *reference IMD*: the interface floor | output only |
| Noise & S/N | *interface floor* = noise of the reference input; within 3 dB of it: *interface limit* | no floor |
| Gain & phase, Tape response | **required**: H = output / reference, phase, delay, coherence | **not available** |
| Stepped sine | gain = tone at the output − tone at the reference | gain = tone at the output − generator level |
| Output Z, Crosstalk, Speed & flutter, Test tape, Player | not used (output levels only) | same |

**Where to tap the reference:**

- **As close to the device input as possible**, with a Y-cable at the input, not at the interface; a long cable or adapter between the tap and the device counts as part of the device.
- **After a divider or attenuator**: for a phono preamplifier after the −40 / −60 dB attenuator, so its value drops out.
- **Power amplifier:** reference at the amplifier input; output through the load and divider, with the divider's attenuation in *Divider [dB]*.
- **Tape recorder:** reference at the record input, output from the off-tape monitor.

## Which wiring

**Stereo** (default) – each channel has its own reference on the neighbouring input of the same kind:

![Stereo: OUT L through a Y-cable to IN 1 (reference L) and device L, device L output to IN 2; OUT R to IN 3 (reference R) and device R, device R output to IN 4](wiring/stereo_default.jpg)

Use it for **frequency response and phase** (Gain & phase, Stepped sine, RIAA): the inputs' own response cancels within each pair.

**Stereo, references first** – references on inputs 1–2, device outputs on 3–4:

![Stereo, references first: OUT L through a Y-cable to IN 1 (reference L) and the device input L, device output L to IN 3; OUT R to IN 2 (reference R) and the device input R, device output R to IN 4](wiring/stereo_reference_first.jpg)

Use it for **distortion, noise and crosstalk** on an interface whose inputs 3–4 are better (MOTU M4: rear line inputs). For frequency response there, reference and output sit on different kinds of input and their difference would count as the device's (on an M4 +2.15 dB at 20 Hz). Measure that difference once with [loop correction](response.html#loop-correction) and it is taken out; or use *Stereo*.

**Stereo, one reference** – one reference (from OUT L) for both channels:

![Stereo, one reference: OUT L through a Y-cable to IN 1 (reference for both) and device L, device L output to IN 3; OUT R straight to device R, device R output to IN 4](wiring/stereo_one_reference.jpg)

Input 2 stays free, and both device outputs sit on the same kind of input, so L and R compare cleanly. The tiny difference between the interface's outputs L and R counts as the right channel's. For frequency response use *Stereo*.

**Mono** – one channel, any two inputs as *Reference* and *Device output*:

![Mono: OUT through a Y-cable to the input chosen as Reference and to the device, the device output to the input chosen as Device output](wiring/mono.jpg)

For single-channel devices, a stereo device **one channel at a time**, an interface with **two inputs**, the most accurate single channel (MOTU M4: IN 3 → IN 4, both rear line inputs) and the interface loop. Two-channel tasks (Crosstalk, azimuth) need a stereo wiring.

**External DAC (USB), no reference** – the DAC plays on its own clock, the interface outputs are silent:

![External DAC (USB), no reference: the PC sends the signal over USB to the DAC; DAC output L to IN 3, R to IN 4; optionally a load resistor (32 or 300 ohm) from each output to the common ground, the same value chosen in On the device output](wiring/external_dac.jpg)

Gain & phase and Tape response are off (Stepped sine measures the response against the generator level); there is no reference row. A pinned trace of a loop measurement (TRACES → Pin) can stand in for the interface floor.

| Situation | Wiring |
| --- | --- |
| Stereo device: response, phase, RIAA | **Stereo** |
| Stereo device: distortion, noise, crosstalk (M4) | **Stereo, references first** |
| One reference is enough, input 2 needed elsewhere | **Stereo, one reference** |
| Two inputs, single-channel device, best single channel, interface loop | **Mono** |
| USB DAC, headphone amplifier with a DAC | **External DAC (USB), no reference** |

| Purpose | Wiring | Why |
| --- | --- | --- |
| Quick overview, adjusting (bias, pots), both channels at once | **Stereo** | one wiring for everything, both channels live |
| L−R balance, volume pot tracking, tape azimuth | **Stereo** | L−R is computed from both channels measured **at the same time**; two runs one after the other cannot give it |
| Crosstalk | **Stereo, references first** | needs two output inputs at once |
| Final distortion and noise figures | **Mono** IN 3 → IN 4, one channel at a time (or *references first*) | output and reference on the best inputs |
| Final frequency response, RIAA | **Mono** IN 3 → IN 4, or **Stereo** | the inputs' own response cancels |

**Mono is the most accurate, but not for everything:** one channel at a time means twice the work and re-cabling, and it gives no L−R comparison, no crosstalk and no azimuth; a device that changes over time (tape, an amplifier warming up) is not in the same state for both runs. On an M4 the difference between wirings is a few dB in the distortion floor and a fraction of a decibel below 70 Hz – it does not change the result for a device well above the M4's floor (0.01 % = −80 dB is 20 dB above it). Mono pays off for devices close to the floor.

**Common mistakes:**

- A device output on an input the wiring does not expect – the cables listed under *Wiring* tell what each input should carry; Crosstalk then reports *No test signal*.
- Reference and output swapped – the gain comes out with the wrong sign.
- A half-inserted reference plug: the reference then carries only crosstalk (about −85 dBFS on an M4) and THD+N reads per cents. The THD+N meter, IMD, Multitone and the sweeps compare the reference with the generator and warn *Reference … dB below the generator · check the reference cable* when it is more than 40 dB low (20 dB with the outputs and that input calibrated; its *Divider* is taken into account).
- Reference tapped at the interface instead of the device; a phono reference before the divider.
- A power amplifier output straight into the interface – always through a load and divider.

## Devices

| Device | Wiring | Step by step |
| --- | --- | --- |
| Line-level device (preamplifier, filter, converter, cable) | *Stereo*: OUT 1 → device input L and IN 1, device output L → IN 2; OUT 2 → device input R and IN 3, device output R → IN 4 | the [tasks](tasks.html) |
| Power amplifier | *Stereo, references first*, through a load and an attenuator – **never straight** | [Power amplifier](howto-amplifier.html) |
| Headphone amplifier, USB DAC | *Stereo, references first* or *External DAC (USB)*, through a load box | [Headphone amplifier and USB DAC](headphone-amp.html) |
| Phono preamplifier | *Stereo*, through a −40 / −60 dB attenuator, the reference after it | [Phono preamplifier](response.html#phono-preamplifier-deviation-from-riaa) |
| Tape recorder | *Stereo*: OUT → record input and reference, the monitor (off-tape) output → IN 2 / IN 4 | [Tape recorder](tape.html) |
| Turntable (test record) | *Stereo*: turntable → phono preamplifier → IN 2 / IN 4 (*Stereo, references first*: IN 3 / IN 4); the interface outputs are not used | [Turntable and test record](turntable.html) |
| CD player, streamer | the test file; the player's output → IN 3 / IN 4 | [Player](player.html) |

Levels in dBFS and which level the generator plays: [Levels](levels.html).
