RF Amplifier Calculator

High-Frequency BJT Amplifier Design Tool

DESIGN INPUTS

RF Amplifier Design Parameters

Workflow: Specify all parameters below, then click "Calculate RF Design" for complete component values.
1Amplifier Type
2Frequency & System Parameters
Operating frequency
Power gain in dB
Voltage gain ratio
3DC Bias Parameters
Collector current
≈ Vcc/2
4RF Transistor Parameters
Transition frequency
Output capacitance
Input capacitance

Calculation Formulas Reference

DC Operating Point:
VE = 1.5 V (typical for stability)
VB = VE + 0.65 V
VC = VCE,Q + VE
IE = (β+1)/β · IC
IB = IC / β
Emitter Resistor:
RE = VE / IE
Bias Divider (stiff: I_div = 10×IB):
R2 = VB / I_div
R1 = (VCC - VB) / I_div
RF Choke (Collector):
L_RFC ≈ 100 µH (typical for HF/VHF)
XL = 2π·f·L ≫ RC (provides DC path, high RF impedance)

Transconductance:
gm = IC / VT
where VT ≈ 26 mV (thermal voltage at 25°C)
Dynamic Resistances:
r_e = VT / IE ≈ 26 mV / IE
r_π = β / gm
Input Capacitance (Miller approximation):
Cπ ≈ gm / (2π·fT) - Cob
where fT = transition frequency
Unmatched Impedances at frequency ω = 2π·f:
Xc_π = 1 / (ω·Cπ)
Zin ≈ r_π || Xc_π (parallel combination)
Zout ≈ 1 / (ω·Cob) (capacitive)

Simplified µ-factor (without S-parameters):
Av_unmatched = gm · Zout
feedback_factor = Cob / (Cob + Cπ)
µ = 1 / (feedback_factor · Av_unmatched)
Stability Condition:
µ > 1 → Unconditionally stable
µ < 1 → Potentially unstable (may oscillate)
Recommended: µ ≥ 1.3 for safe margin
Stabilization Techniques:
1. Series base resistor: R_stab ≈ 100 Ω
2. Collector-base neutralization: R_neut ≈ 1/(ω·Cob)
3. Increase unbypassed RE
4. Ferrite bead on base or collector

Wideband (L-Network Matching):
Step-Up (Zin > Zs):
Xs = √(Zin · Zs - Zs²)
Xp = Zin² / Xs
L_series = Xs / ω
C_parallel = 1 / (ω·Xp)
Step-Down (Zin < Zs):
Xp = √(Zs · Zin - Zin²)
Xs = Zin² / Xp
C_series = 1 / (ω·Xs)
L_parallel = Xp / ω
Narrowband (Tuned Circuits):
Parallel LC Tank (Output):
Rp = desired parallel resistance (e.g. 5 kΩ)
L = Rp / (ω·Q)
C = Q / (ω·Rp)
Resonant frequency: f0 = 1 / (2π√(LC))
Series LC Tuning (Input):
L = Zin / (ω·Q)
C = 1 / (ω²·L)
Bandwidth:
BW = f0 / Q
Higher Q → Narrower bandwidth, higher selectivity
Output Coupling:
Tap ratio = √(ZL / Rp)
or Link coupling: k ≈ 1/Q (critical coupling)

Wideband Voltage Gain:
Av ≈ gm · ZL
where ZL = load impedance (typically 50 Ω or 75 Ω)
Narrowband Voltage Gain:
Av ≈ gm · Rp
where Rp = parallel tank impedance (much higher than ZL)
→ Much higher gain than wideband
Power Gain:
Gp(dB) = 20·log10(Av)
(assumes matched input and output)
Gain Design (User-Specified Gain):
Gain Conversion:
Av = 10^(Gp_dB/20)
Gp(dB) = 20·log10(Av)
Wideband Gain Design:
With emitter degeneration:
Av = ZL / (RE1 + r_e)
→ Solve for RE1: RE1 = ZL / Av_desired - r_e

Maximum gain (no degeneration):
Av_max = gm · ZL
Narrowband Gain Design:
Av = gm · Rp_tank
→ Solve for Rp: Rp_tank = Av_desired / gm

Then calculate tank components:
L = Rp / (ω·Q)
C = Q / (ω·Rp)
Bandwidth: BW = fc / Q
VSWR (Voltage Standing Wave Ratio):
VSWR = (1 + |Γ|) / (1 - |Γ|)
where Γ = reflection coefficient
Ideal: VSWR = 1:1 (perfect match)
Good: VSWR < 2:1