FAQ

Click a question to expand it. For the full walkthrough, see the Manual.

How do I measure…

…the distortion of an amplifier?

Wire it as in the wiring page (a power amplifier always through a load and a divider), pick THD+N meter, set 1 kHz and a level, and press SINGLE. For the level where it starts to clip, use THD vs level; for the whole audio band, THD vs frequency.

…the signal-to-noise ratio?

Pick Noise & S/N, keep the device input connected to the interface output, set the test tone to the rated level and press SINGLE. AudioLab measures the tone, silences the generator and measures the noise, unweighted and A-weighted. Manufacturers usually quote the A-weighted value.

…channel separation of a stereo device?

Use a stereo wiring, pick Crosstalk and press SINGLE. Each frequency is played into one channel only and the leak into the other channel is measured, both ways. Separation is the negative of the crosstalk in dB.

…a headphone amplifier with a USB DAC?

Choose the wiring External DAC (USB), no reference and the DAC in CONNECTIONS; the test signal then plays through the DAC in Windows exclusive mode, and the DAC's outputs go to In 3 and In 4. Distortion, noise, crosstalk and the level meter work as usual; Stepped sine gives the frequency response, since the DAC runs on its own clock and there is no reference. With a load resistor chosen in On the device output (16–600 Ω), THD vs level gives the power at 1 % THD+N, and Output Z the output impedance.

…a CD player, streamer or portable player?

Pick Player, create the test file in SIGNAL (CD: 44,100 Hz, 16-bit) and copy it to the player. Connect the player's output to the device-output inputs, press RUN and play the file from the start. AudioLab recognises each part as it plays. Use WAV or lossless FLAC, switch off EQ and resampling, and keep the volume fixed.

…a tape recorder?

Record the test signal and monitor from the playback head. Speed & flutter measures speed, wow, flutter, azimuth and dropouts from a 3150 Hz tone (or a test tape with Play test signal off); Tape response gives the record-to-playback frequency response. With a test tape, Test tape gives the playback response from its sequence of tones, whatever the tape's speed error. Wow and flutter are given weighted (IEC 60386) and unweighted.

About AudioLab

Where does AudioLab come from?

It grew out of the author's own scripts for servicing amplifiers and tape recorders at the workbench, which drove a signal generator and an oscilloscope. AudioLab does the same work through an audio interface, by the methods described in the manual, and is free.

How reliable are the results?

The calculations are tested against known signals and against simulated devices whose distortion, noise and crosstalk are set exactly. Every setup has its own limits, so check yours with a loopback of the interface and compare the results with a known reference before relying on them.

Hardware & setup

Which audio interfaces work?

AudioLab records and plays through the driver the interface's manufacturer supplies with it (an ASIO® driver, such as MOTU's). It is developed for the MOTU M4 (four inputs: reference and output of both channels). Other interfaces whose manufacturer supplies such a driver, with at least two inputs and two outputs, should work; with two inputs use the Mono wiring. Measure the loopback floor of any interface before trusting results near it.

ASIO compatibleASIO is a registered trademark of Steinberg Media Technologies GmbH
Why record the signal before the device too?

The reference shows what the generator and converters add by themselves. When the device result is close to the reference, the setup is the limit, not the device. It also gives the true gain and phase of the device in Gain & phase.

Can I try AudioLab without an audio interface?

Yes. Choose AudioLab Simulator (no hardware). It simulates a loopback cable, a line preamplifier, a power amplifier, a headphone amplifier, a USB DAC, a phono preamplifier, a tape recorder and a turntable playing a test record, with known distortion, noise, hum, crosstalk, wow and flutter and azimuth, wired like the chosen wiring. Simulated data are not measurements.

Why is the generator frequency 999.76 Hz instead of 1000 Hz?

The generator plays the nearest centre of an FFT bin (999.76 Hz at 48 kHz; the figure depends on the sample rate and the FFT length). The tone and its harmonics then fit whole cycles into every FFT block and do not leak into neighbouring bins, which makes distortion and noise readings more accurate.

Results & files

How do I get a protocol of a measurement?

Press Report. AudioLab writes a folder with a Markdown protocol, the data and the chart for MD Visor and opens it there. Fill in the device name and your conclusions and export to PDF.

What is in an .audiolab file?

The curves on screen, their axes and the measurement conditions, as GZip-compressed JSON. It is AudioLab's own format for kept traces (TRACES → Save… and Load file…); use Export (CSV) to exchange data with other programs.

The CSV opens as one column in Excel.

In Settings → CSV export choose Semicolon, decimal comma for Excel with Czech or most European regional settings.

Privacy & data

Does AudioLab send anything anywhere?

No. There is no server, no account and no telemetry. Settings, calibration and error logs stay on your computer under %LocalAppData%\AudioLab, measurements wherever you save them. See the privacy policy.