What to measure

Where to start with each kind of device: which tasks matter, and a page per device with the wiring, the settings and what a good result looks like. How each control works is in the Manual, the formulas are on the Methods page.

Before you start

  1. Measure the interface itself first. Connect OUT 1 to IN 1 and IN 2, OUT 2 to IN 3 and IN 4 (no device) and run THD+N meter and Noise & S/N. That is the floor: no device can measure better. A device that reads the same as the loop is better than the interface can tell, not “as good as the interface”. A good USB interface reaches about 0.0005–0.001 % THD+N and 110 dB S/N.
  2. Note the conditions: level (dBFS, V or W), frequency, load, volume knob position. AudioLab writes them into every export and report.
  3. Watch the reference. It shows the measurement path alone. When the device reads close to its reference, you are measuring the interface, not the device.
  4. Start low (−40 dBFS) and raise the level; set Settings → Generator output limit before measuring sensitive inputs or loudspeakers.
  5. Watch the INPUTS meters and the status line. The meters in the top bar show every input live; a red row is near clipping. The status line warns when a reference lies far below the generator (a plug not fully in) and, with the inputs calibrated, when it reads away from its calibration (a gain or volume knob moved since).

Which wiring (interface with front and rear inputs, e.g. MOTU M4)

On a MOTU M4, IN 1 and IN 2 are the front combo inputs: even at minimum gain they pass a preamplifier and are worse than the rear line inputs IN 3/4 (THD+N −100 against −106 dB, response specified only from 70 Hz). With four inputs, a stereo measurement with references always puts one pair on the front inputs, so choose what goes there:

MeasurementWiringWhy
Frequency response: Gain & phase, Stepped sine, RIAAStereoreference and output of each channel sit on the same kind of input, so the inputs' own response (the front inputs' roll-off below 70 Hz) cancels
Distortion and noise: THD+N, THD sweeps, IMD, Noise & S/N, crosstalkStereo, references firstthe device outputs go to the better rear inputs IN 3/4; the references on the front inputs only show the floor
One channel, as accurately as possibleMono, reference IN 3, output IN 4both on the rear line inputs

The interface loop, step by step in Measure your interface first, shows how much worse the front inputs are on your unit. All wiring modes and what the reference does in each task: Wiring and the reference in detail.

TermMeaningBetter is
THDharmonic distortion only (H2, H3 …)lower
THD+Ndistortion and noise together: everything that does not belong in the signallower
S/Nhow much stronger the signal is than the noisehigher
IMDdistortion with two tones at once (tones mixing)lower
Frequency responsehow evenly bass and treble passflat (±0.5 dB)
Crosstalkhow much of one channel leaks into the othermore negative dB
Output impedancehow much the output voltage drops under a loadlower
Damping factorload ÷ output impedance: how firmly an amplifier controls a speakerhigher

Percent and dB: 1 % = −40 dB · 0.1 % = −60 dB · 0.01 % = −80 dB · 0.001 % = −100 dB · 0.0001 % = −120 dB.

Overview: which task for which device

●●● main measurement, always · ●● useful · ● sometimes · – makes no sense. A player (CD, streamer, portable) is measured with the Player task only: one play of the test file gives everything marked ✓. A turntable is measured with its phono stage from a test record (Test record); the phono stage alone, through an attenuator, in the Phono column.

TaskPower ampHeadphone ampPre­ampPhonoFilter, crossoverUSB DACPlayerTapeTurn­table
Level meter●●●●●●●●●●●●●●●●●
Spectrum●●●●●●●●●●●●●●●●●●
THD+N meter●●●●●●●●●●●●●●●●●✓●●●–
THD vs level●●●●●●●●●●●●●●●✓●●●–
THD vs frequency●●●●●●●● (inverse RIAA)●●●–●–
IMD●●●●●●●●●✓●–
Multitone●●●●●●●●●●–●–
Gain & phase●●●●●●●●●●●●●––––
Stepped sine●●●●●●●●●●●✓●–
Noise & S/N●●●●●●●●●●●●●●●●●✓●●●–
Crosstalk●●●●●●●●●●●✓●●–
Output Z●●●●●●●●●●●–●–
Speed & flutter, Tape response, Test tape–––––––●●●●● (Speed & flutter)
Player––––––●●●––
Test record––––––––●●●

Devices

DeviceMain measurements
Measured devicesfull protocols of real devices measured this way: an audio interface, a USB audio card, a headphone amplifier
Your audio interface – firststep by step in a loop: calibration, input noise, THD, the loop correction, crosstalk, IMD – the floor every other measurement is read against
Power amplifierpower at 1 % THD+N, THD+N at 1 W, S/N, damping factor – through a load and an attenuator
Headphone amplifier and USB DACpower into 32 / 300 Ω, output impedance, noise for IEMs; a DAC's dynamic range and jitter · step by step
Preamplifier, filters, equalizers, cablesgain and flatness, channel balance, headroom, noise; filter slopes and crossover phase
Phono preamplifier (RIAA)RIAA accuracy, hum and noise, overload with inverse RIAA
Tape recorderspeed, wow and flutter, azimuth, response, MOL, S/N
Turntable and cartridgefrom a test record: speed, wow & flutter, crosstalk and azimuth, response, tracking, anti-skating, arm resonance, rumble · with just a USB sound card, no interface
USB audio cardstep by step: the input as External ADC, the output as External DAC, Windows settings, and the pitfalls – ground loop, 997 Hz, the Windows volume, digital full scale
CD player, streamer, portable playereverything from one play of the test file, the J-test included

Problem → measurement

ProblemMeasure
It humsSpectrum: 50 Hz (ground, induction) or 100 Hz (supply filtering)?
It hissesNoise & S/N, compare with the reference and the interface loop
Distorts when loudTHD vs level: where clipping starts
One channel sounds differentGain & phase with both channels (L−R), THD+N of both
Too little bass or trebleGain & phase: where the −3 dB points are
Headphones sound different on another amplifierOutput Z (rule of 1/8)
Records sound too bright or dullPhono preamplifier: Stepped sine with Compare with phono curve = RIAA
Tape recorder or turntable waversSpeed & flutter, then its Spectrum: the frequency of the strongest line tells the part (0.56 Hz = the platter or record at 33⅓ rpm, higher = capstan, pinch roller, motor; with the tape speed and roller diameters in Settings the capstan and pinch roller lines are named)
Records: one channel duller, distorting or leaking more than the otherTest record, Setup view: tracking force and anti-skating first, the azimuth last; Response, Tracking and Crosstalk show the detail
Turntable: boomy bass, feedback or sensitive to footstepsTest record: Resonance (the arm and cartridge should resonate at 8–12 Hz) and rumble from the silent groove
Tape recorder has dull trebleTest tape, azimuth (Speed & flutter at 10 kHz), then Tape response (bias)
CD player, streamer, portable playerPlayer
Hum or interference that comes and goesSpectrum → Spectrogram: when it appears and at which frequency
Sounds harsh, but THD+N looks fineTHD+N meter → Scope: the shape of the residual (crossover, clipping, oscillation); Multitone for music-like signals
Adjusting a device (bias, quiescent current, a trimmer)Multitone or THD+N meter with RUN: the whole band or one point, live
A digital source sounds roughPlayer: the J-test shows jitter

A routine that always pays

  1. Interface loop (OUT → IN): save it as the floor.
  2. INPUTS meters or the Level meter: no input near 0 dBFS (a red row, CLIPPING).
  3. Spectrum: a quick look for hum and interference.
  4. THD+N meter at a sensible level (1 W, 1 V, −10 dBFS).
  5. Gain & phase or Stepped sine: flatness.
  6. Noise & S/N.
  7. By device: THD vs level (power, clipping), Crosstalk, Output Z.
  8. Keep each result as a trace for before/after; Save… a trace in TRACES to archive it.
  9. Report: a protocol for MD Visor with the device name and your conclusion.