Download

AudioLab downloads

Windows 10/11, 64-bit, free of charge. Measurements need an audio interface and the driver its manufacturer supplies for it (an ASIO® driver, for example from MOTU; AudioLab is developed for the MOTU M4). The built-in simulator works without one.

ASIO compatibleASIO is a registered trademark of Steinberg Media Technologies GmbH
v0.3.8

Microsoft Store

AudioLab is distributed through Microsoft Store. Updates are delivered through the Store.

Open in Microsoft Store

Install the driver of your audio interface from its manufacturer before the first measurement. Check the measurement floor of your setup with a loopback (see the manual).

Release notes

What's new in AudioLab

$ v0.3.8
  • Turntable setup: the track strip above Details no longer repeats itself once the Setup view is open – Setup already shows the same tracks, with its own colours for what to play now.
  • Audio interface list: Windows audio device (no ASIO) now lists after your ASIO drivers, with the simulator last.
$ v0.3.7
  • No ASIO interface needed for a turntable: choose Windows audio device (no ASIO) as the audio interface to measure a turntable (or a test tape, or a player) through nothing but a USB sound card – no ASIO driver, no separate interface. The wiring locks to the card’s own input and only the tasks that listen (Test record, Test tape, Player, Spectrum, Level meter, Speed & flutter) are offered. Step by step →
  • Turntable setup: the Tracking force step no longer reads a clipped tracking track as mistracking – once Signal warns of input overload, its summary line says so instead of showing distortion figures for a track the input could not record cleanly.
  • Fixed a crash analysing a test record’s sweep at 48 kHz: the peak search could run past the end of the spectrum as the sweep neared the interface’s Nyquist frequency, where at 96 kHz the tone had already faded below the noise floor.
$ v0.3.5
  • USB audio cards: the new wiring External ADC measures a USB recording device – a USB card’s input, a USB phono preamplifier – with the generator of your interface; External DAC shows the Windows playback volume. Set to 0 dB sets the Windows volume of both, which on a USB card is a gain in the card. A rate the card lists but will not record at gets its next format, or a plain message. Step by step →
  • Output impedance: the Off row of Measured loads takes the load a box leaves on the output when switched off (its divider) into the formula – into 300 Ω it read 10 % low without it. A load switched on before it is chosen is noticed, and the open reading kept. Headphone amplifier, step by step →
  • Dividers: the calibration wizard measures a load box’s divider in volts and takes a reading only once the level stands still.
  • Gaps in the recording are found in the signal: a sweep reads the step again. A 997 Hz key (AES17), so the harmonics miss a card’s own lines at whole kilohertz. The generator’s limit goes up to 0 dBFS, with a warning; level sweeps of an ADC are drawn over the input volts.
  • The reference inputs are checked against their calibration only from 100 Hz to 10 kHz; RIAA comparison without a reference is set to 0 dB at 1 kHz; the ANALYSIS panel says when loop correction applies.
  • Turntable setup: the azimuth card states the spread measured between tracks and records, and says to leave the screw when a turn does not move the figure.
  • The manual: measure your interface first, step-by-step guides for a headphone amplifier and a USB audio card, and Measured devices – full protocols of devices measured with AudioLab.
$ v0.3.3
  • Turntable setup, step by step: the new Setup view reads the test record as it plays and says what to adjust – speed, tracking force, anti-skating, azimuth – which way, and which tracks to play again. It also catches the wrong record, a missing phono correction, input overload and a loose contact. How to use it →
  • Azimuth from a whole play of the one-channel tracks, within ±2 dB; anti-skating from all the tracking tracks.
  • Phone: the figure of the step being adjusted, large, with OK / check.
$ v0.3.2
  • Turntable → Test record: a new task that measures a turntable, its tonearm and cartridge from the Ortofon Test Record or Analogue Productions’ The Ultimate Analogue Test LP. Play the tracks in any order; each one is recognised as it plays. Speed, wow & flutter, crosstalk and azimuth, channel balance, response against the record’s curve, tracking ability, anti-skating, the arm and cartridge resonance, rumble, IMD, pink noise and the polarity from the square wave – with OK / check, views for each, and every track in Copy and the report.
  • The record’s stepped sweeps, its −20 dB tones and lateral against vertical cuts (by the phase of L and R) are recognised; the tracks are named as on the sleeve (A1–A10, B1–B6); clicking a track before playing it says which one it is.
  • The Azimuth view for turning the headshell: one point per pair of plays, read over the whole tracks, with both crosstalk figures and what to do next.
  • Phone: the measurement bar on a phone in the local network, through a QR code, with RUN/STOP, SINGLE and REL – the figure to turn a trimmer by, at the trimmer.
  • Phono stage: the attenuator before the device in CONNECTIONS (−40 dB MM, −60 dB MC), so the level and its keys (5 mV) are given at the stage’s input; S/N only with the test tone at the output; another phono curve redraws the steps without a new sweep.
  • Level meter: the Large key writes each input’s level large over its bar, readable across the room; REL takes the reference of an input that had no tone when pressed once its tone comes; the tone is read at the generator’s frequency, not the hum beside it.
  • Tape: the test tape’s tone can be chosen or typed when the deck runs far off speed; the distortion limit of a tape is read on THD, not THD+N; a test tape’s full-track bass tones are kept in the series; the L−R time of Tape response is read from the phase slope.
  • Generator frequency keys 500 Hz and 12 kHz; Enter takes a value typed in a field; Details show everything Copy gives, take at most a third of the room and follow new lines; a name typed with .png or .svg in Export saves the chart as an image.
  • The manual: tape recorder and turntable set up step by step on real machines, with figures – bias, record level and EQ, the tracking force seen in the measurement, a desktop computer through a USB isolator.
$ v0.2.3
  • Level meter keys for turning a trimmer: REL sets each input’s level as 0 dB, so a test tape’s treble reads against its 1 kHz; Max hold leaves a peak-hold tick at the highest level until you reset it, for a head’s azimuth or a recorder’s bias past its maximum.
  • Zoom shows each input against its held maximum to a hundredth of a dB; Balance compares In 1/In 2 and In 3/In 4 and turns green within a tolerance set in Settings.
  • Gain of each output against its reference, with the levels averaged over a time set in Settings; hum and noise left when the tone stops are not taken for the tone.
  • Azimuth also as the tilt of the head in degrees, from the track spacing set in Settings and the tape speed.
  • After STOP the Speed & flutter keys switch the view between azimuth, spectrum and the deviation over time with their last results.
$ v0.2.1
  • Loop correction: the response of the interface’s own inputs, measured with the device left out, is subtracted from later responses, so only the device is left.
  • Tape: a live azimuth view in Speed & flutter with the L/R offset in µs and its history.
  • Spectrum: the Peaks key names the ten strongest lines of each output, judged against the local floor; Copy lists them.
  • Readings in volts on every calibrated input; in the level meter calibrated inputs in dBV beside uncalibrated ones in dBFS, the diamond being the real peak voltage.
  • Large readouts in the measurement bar and decade ticks on log axes.
  • Late driver callbacks are detected and the damaged capture is discarded and logged; after a generator change the averaging starts anew.
  • Every measurement has its own page in the online manual, with figures.
$ v0.2.0
  • Analyser views: keep traces and pin one as the interface floor, an Info window with every cable of the wiring, REF and dBc keys, and a Scope view of the signal and its residual beside THD+N.
  • Multitone: 31 third-octave tones with TD+N in the gaps. Spectrogram of the last minute, noise density per √Hz, ITU-R 468 weighting and an AES17 filter for class D amplifiers.
  • Sweeps drawn over the generator level, the output level or the output power, as distortion in dB or % on a log axis, single harmonics H2–H5 or the output level; switching only redraws.
  • SINAD instead of THD+N for the whole application (Settings → Analysis), as converters are quoted.
  • The device’s delay is measured before sweeps, Crosstalk and Noise & S/N, so a tape recorder’s heads are waited out at any speed.
  • Tape: weighted wow and flutter (IEC 60386 / DIN 45507, W.RMS and 2σ) and the spectrum of the speed deviation up to 1 kHz, with the capstan and pinch roller lines named.
  • Phono: inverse RIAA on the generator and the deviation from RIAA in Gain & phase and Stepped sine, which now also gives the phase.
  • Input meters (VU and PPM) in the ribbon, a reference check against the generator level and a warning when a level knob has moved since calibration.
  • J-test in the player test file, measured load resistors, S/N against the distortion limit, a stereo wiring with one reference, and fixes from the verification on a MOTU M4.
$ v0.1.2
  • Headphone amplifiers with a USB DAC: the generator plays through a Windows audio device in exclusive mode; the wiring External DAC needs no reference.
  • Stepped-sine frequency response, also without a reference; output impedance and damping factor; headphone loads 16–600 Ω with power in mW.
  • Players with their own converter measured from a test file AudioLab writes (WAV, 16/24-bit dithered or float): level, THD+N, linearity, dynamic range, noise, crosstalk, response, IMD.
  • Test tape: the playback response from a test tape’s sequence of tones, whatever the tape’s speed error.
  • Tones from another clock (external DAC, player) are analysed with the Blackman-Harris window, which keeps the THD+N floor where it belongs.
  • Long results scroll, so the chart stays in view. Simulated headphone amplifier and USB DAC.
$ v0.1.1
  • Crosshair for reading values, snapping to harmonic peaks; the chart in its own large window (Enlarge).
  • Copy of the result as text; chart export as PNG or SVG, light or dark.
  • Measurement protocols for MD Visor draw every chart natively, spectra and tape included.
  • The calibration wizard with an external DAC leaves the interface outputs as they are.
$ v0.1.0
  • First release: measurements chosen by task, with RUN/STOP and SINGLE as on an oscilloscope.
  • Reference and device output captured together; both stereo channels measured at once, with wiring presets and L/R channel keys.
  • Spectrum, THD+N meter, THD vs level and frequency, IMD (SMPTE, DIN, CCIF) and IMD vs level.
  • Gain & phase from a periodic chirp with coherence, corner frequencies, delay and L−R balance.
  • Noise & S/N, unweighted and A-weighted, and crosstalk across the band.
  • Level meter for all inputs (dBFS, V, dBV, dBu, clipping) and a calibration wizard with a live level; amplifier power in W with the power at 1 % THD+N.
  • Tape recorder: speed, wow and flutter (RMS and 2σ peak), azimuth, dropouts and record-to-playback response.
  • Calibration in volts, CSV export, saved measurements and overlays, and measurement protocols for MD Visor.
  • Built-in simulator of a preamplifier, power amplifier and tape recorder; generator output limit; local error log.