One groove · two channels
Stereo Groove Simulator
Explore how a single stylus follows the two 45° groove walls. Change the left and right signals, then watch their lateral sum and vertical difference become one motion. To measure your own turntable from a test record, see Turntable and test record and Turntable setup, step by step.
Groove cross-section
The V-shaped groove is exaggerated. Orange is the inner (left) wall; blue is the outer (right) wall.
Looking down the groove
Two channels, one stylus
Ideal 45/45 geometry: x = A(L + R)/√2, z = A(L − R)/√2. Positive z means deeper in this drawing. L and R are normalized wall displacements obtained by integrating the selected signal; the coil-voltage rows follow their velocity. The ideal MM model assumes 5 mV peak at 5 cm/s peak wall velocity. It omits RIAA equalization, cutter and cartridge bandwidth, and tracking limits, so it does not predict a particular record or cartridge. The groove shape and stylus are schematic.
What each setting does to a measurement
Change one setting and watch the corresponding measurement. The examples explain cause and effect; they are not calibration targets for a particular cartridge. On a real turntable AudioLab reads the azimuth, the tracking force and anti-skating and the speed from a test record in the Setup view, and the arm resonance and the treble response in the other views; it does not read the tracking angle or VTA.
Azimuth
Tilt of the stylus viewed from the front. A one-channel test tone reveals unequal leakage into the other channel.
About 20–30 dB at 1 kHz is common; some cartridges specify over 40 dB. Separation usually falls at high frequencies. The selected value sets both directions at zero tilt.
The tilt effect is illustrative. Real crosstalk also depends on the cartridge generator, test record and setup.
Tracking and anti-skating
A strong 315 Hz test groove challenges the stylus. Low tracking force can cause mistracking; anti-skating error can make one wall lose contact first.
Demo cartridge target: 2.0 g. Follow the actual manufacturer's force range. Negative offset means too little anti-skating, positive too much; the percentage is model bias, not a dial setting. −100 % is no anti-skating at all.
MM electrical load
The cartridge coil and the total cable-plus-input capacitance form an electrical filter. This view isolates that electrical effect.
Example MM coil: 480 mH and 750 Ω. Reference load: 47 kΩ / 200 pF. Capacitance includes the cable and phono input.
Alignment and VTA
The stylus should follow the groove tangent and meet the groove at its intended vertical angle. These sketches show orientation only.
Zero means the stylus matches the local groove tangent and the cartridge's intended vertical angle. A real pivoted arm's error varies across the record.
Arm and cartridge resonance
The tonearm's effective mass moves against the stylus suspension. Their combination sets the low-frequency resonance.
Use compliance near the resonance frequency when known; a 100 Hz datasheet value may differ.
Speed and wow
A steady speed error shifts the pitch. A slow periodic variation makes a test tone waver.
At 33⅓ RPM, one revolution takes 1.8 s (about 0.56 Hz). This wobble may also come from an off-center test record.
When a measurement looks wrong
These are clues, not unique diagnoses. Change one setting at a time and repeat the same test track.
| What you see or hear | What to check |
|---|---|
| One-channel leakage differs by direction | Azimuth, after confirming tracking force and anti-skating. |
| One channel distorts first on a loud test groove | Right first: the tracking force, then too little anti-skating. Left first: too much anti-skating. Then the stylus condition. |
| One channel distorts more on every tracking groove, also the quiet ones | Anti-skating: right worse – too little, left worse – too much. |
| Both channels change in the treble | MM load resistance and total cable-plus-input capacitance; also stylus and record condition. |
| Large subsonic peak or strong warp response | Effective arm mass and cartridge compliance; verify with a low-frequency test track. |
| Pitch is wrong or wavers periodically | Average platter speed; then motor, drive and test-record centering. |
| Distortion worsens toward the inner groove | Horizontal alignment, stylus profile and wear; the shorter groove wavelength increases the challenge. |